Harris Tip Chart - Hornet Cutting Systems- oxy-acetylene cutting torch tip size chart ,Harris Tip Chart Plate Thickness (Inches) 6290 Tip Size 6290-s Tip Size Oxygen (PSIG) Acetylene Pressure (PSIG) Cutting Orifice (# Drill Size) Light gauge to 0.187 000 - 15-20 5-15 #68 .187 to .375 00 - 20-25 5-15 #64 .375 to .625 0 - 35-40 5-15 #60 .625 to 1.000 1 1S 35-40 5-15 #56 1-2 2 2S 40-45 5-15 #52 2-3 3 3S 45-50 5-15 #48 Oxygen & Acetylene Gas Pressures - NHADATHICKNESS PREHEAT CUTTING OXYGEN ACETYLENE 1/8 - 3/8" 70 67 20 - 30 3 3/8 - 3/4" 62 58 30 - 40 5 3/4 - 1" 57 54 40 - 45 5 1 1/2 - 2" 54 51 45 - 50 5 NOTES: Tables show approximate gas pressures for welding or cutting. Tip size numbers vary among manufacturers, so orifice sizes are shown in "number drill" sizes. LENS SHADE 3-4 4-5 5-6 4-5 5-6 6 ...
Set supply pressure for cutting oxygen pressure at supply regulator to approximately 90 PSI Adjust Cutting Oxygen pressure on Hi/Low Preheat manifold regulator to the value shown in the chart above STEP #3 Using the manifold regulators, set low pre-heat fuel pressure to the lower of the two pressure values shown in chart above - preliminary setting
Maximum acetylene pressure is 15 PSI and it should not go any higher! The chart presents you pressure values when the torch is used with 25 feetx3/8 inches hose and with tips size 6 and bigger. An additional thing to consider. A flow rate of acetylene cylinder (individual) must not exceed 1/7 capacity of a cylinder in one hour.
Corporate Office 6212 29th Street East Bradenton, FL 34203 Toll Free: (800) 342-8477 Phone: (941) 753-7557 EU Office Kingsfordweg 1043 GR Amsterdam The Netherlands
Types Of Oxyacetylene Welding Torches. Oxy-acetylene welding torches are mainly categorized into two types: one is the low pressure type which is also called as the injector type; second is the equal pressure type. In the low pressure or injector type torch, see figure 1 below, the acetylene pressure is kept below 1 psi (6.89 kPa).
Set supply pressure for cutting oxygen pressure at supply regulator to approximately 90 PSI Adjust Cutting Oxygen pressure on Hi/Low Preheat manifold regulator to the value shown in the chart above STEP #3 Using the manifold regulators, set low pre-heat fuel pressure to the lower of the two pressure values shown in chart above - preliminary setting
Types Of Oxyacetylene Welding Torches. Oxy-acetylene welding torches are mainly categorized into two types: one is the low pressure type which is also called as the injector type; second is the equal pressure type. In the low pressure or injector type torch, see figure 1 below, the acetylene pressure is kept below 1 psi (6.89 kPa).
Corporate Office 6212 29th Street East Bradenton, FL 34203 Toll Free: (800) 342-8477 Phone: (941) 753-7557 EU Office Kingsfordweg 1043 GR Amsterdam The Netherlands
The oxy-acetylene cutting torch primarily works via a combustion process that is caused by the mixture of acetylene and oxygen. This combination process produces aflame with heat exceeding 3000°C, which is enough to cut through mild steel. Mild steel is any steel that has a carbon component that is a maximum of 0.3%.
Cutting Torch Tip Chart Example: If I want to cut 3/4 inch metal look at the metal size chart and go down do 3/4. Then go across the column for the tip size to the acetylene pressure and oxygen pressure. In this case, to cut 3/4 inch metal I will need: Tip Size: 1. 3-5 Pounds of Acetylene. 30-35 Pounds of Oxygen.
Types Of Oxyacetylene Welding Torches. Oxy-acetylene welding torches are mainly categorized into two types: one is the low pressure type which is also called as the injector type; second is the equal pressure type. In the low pressure or injector type torch, see figure 1 below, the acetylene pressure is kept below 1 psi (6.89 kPa).
Corporate Office 6212 29th Street East Bradenton, FL 34203 Toll Free: (800) 342-8477 Phone: (941) 753-7557 EU Office Kingsfordweg 1043 GR Amsterdam The Netherlands
Only the original Koike oxy fuel cutting tips: 102, 102HC, 102-D7, 103, 103-D7, 106, 106HC, 106-D7, 107 and 107-D7 are designed and manufactured to provide high quality cutting, safe operation, longer cutting life, high speed cutting and save gas costs. In addition our 100 series cutting tip can be used to replace Airco® style cutting tips.
Only the original Koike oxy fuel cutting tips: 102, 102HC, 102-D7, 103, 103-D7, 106, 106HC, 106-D7, 107 and 107-D7 are designed and manufactured to provide high quality cutting, safe operation, longer cutting life, high speed cutting and save gas costs. In addition our 100 series cutting tip can be used to replace Airco® style cutting tips.
Corporate Office 6212 29th Street East Bradenton, FL 34203 Toll Free: (800) 342-8477 Phone: (941) 753-7557 EU Office Kingsfordweg 1043 GR Amsterdam The Netherlands
